Lockout/Tagout for Small Teams: The What, the Why and the How

"I just hit the stop button." If you've ever heard that sentence near a machine that's being cleared, adjusted or repaired, this post is for you.

Lockout/tagout, formally 29 CFR 1910.147, "The control of hazardous energy," is one of the rules small employers ask about most. It's also #3 on OSHA's preliminary list of the most frequently cited standards for fiscal year 2026. Here is what it asks for, why it exists, and how a team without a full-time safety department can keep up.

The what

The standard covers the servicing and maintenance of machines and equipment where unexpected energization, startup, or release of stored energy could injure employees. If someone on your team clears jams, changes blades, adjusts belts or repairs equipment, it likely applies.

The employer's job is to establish an energy control program made of three parts: written energy control procedures, employee training, and periodic inspections. There is a narrow exception for cord-and-plug equipment: if unplugging it removes the hazard and the plug stays under the exclusive control of the person doing the work, the standard doesn't apply to that task.

The why

Hazardous energy isn't only electrical. It can be hydraulic or pneumatic pressure, a raised part held up by gravity, a compressed spring, or heat. OSHA puts it plainly: the unexpected startup or release of stored energy can result in serious injury or death to workers.

And here is the detail that changes how people think: push buttons, selector switches and other control circuit type devices are not energy isolating devices. A stop button tells a machine to stop. It does not stop a coworker, a timer or a program from starting it again. Isolation means something that physically prevents energy from flowing: a disconnect, a breaker, a valve, a block.

That's why "be careful" is not a control. Careful people get hurt when the system around them assumes the machine will stay off.

The how: six steps, in order

The standard lists the sequence for applying energy control:

  1. Preparation for shutdown. Know the types and amounts of energy and how to control them.

  2. Machine or equipment shutdown. Use the normal shutdown procedure.

  3. Isolation. Operate every energy isolating device.

  4. Lockout or tagout device application. Each authorized employee applies their own device.

  5. Stored energy. Relieve, disconnect, restrain or otherwise make safe any stored or residual energy.

  6. Verification of isolation. Confirm the machine is actually isolated before work begins (for example, try the normal start control, then return it to off).

Step six is the one most likely to be skipped in a hurry, and it's the one that catches the second power source nobody remembered.

Who removes the lock, and other details that matter

  • Locks first. If an energy isolating device can be locked out, the program uses lockout. Tagout alone is allowed only when the employer can show it gives full employee protection.

  • Devices are identifiable. Lockout and tagout devices must be durable, standardized, substantial, and must show the identity of the person who applied them.

  • The person who applied it removes it. The standard allows an exception only under a documented procedure, when that person is not at the facility, with steps to reach them and inform them before they return.

  • Training by role. Authorized employees (the ones who lock out) learn to recognize energy sources and control them. Affected employees (people who operate the machine) learn the purpose and use of the procedure. Everyone else who works in the area learns not to restart or re-energize locked or tagged equipment.

  • Annual check. Each energy control procedure gets a periodic inspection at least annually.

A small-team starting plan

  1. List the machines your team services or clears.

  2. Pick the one used most. Write a one-page procedure with a photo of each isolation point.

  3. Buy standardized locks and tags, one set per authorized person, with names on them.

  4. Walk the procedure with the people who do the work. Ask them what's missing.

  5. Put the annual inspection on the calendar now.

  6. Ask your team one question: "Which machine do we 'just stop' instead of locking out?" Start there.

Want a simple place to start?

Download the free Why & How Checklist (English and Spanish), which covers the most-cited general industry standards in the same what, why and how format.

Get the free checklist →

If you'd like this kind of practical training onsite for your team, Insight Safety Partners offers OSHA 10 General Industry classes in English or Spanish. Request a quote. OSHA Outreach training is voluntary; participants who complete the class receive a DOL course completion card, which is not a certification or license.

This article is general education, not legal advice. Always read the full standard at osha.gov.

Next
Next

Walking-Working Surfaces for Small Teams: The What, the Why and the How